Welcome to Sprocket School! This project is maintained by volunteer editors. Learn more about how this works.

Best practices: Difference between revisions

From Sprocket School
Jump to navigation Jump to search
No edit summary
No edit summary
Line 18: Line 18:


'''During projection''':
'''During projection''':
* If possible, use 2000 ft. reels and a dual-projector [[changeover]] system. NEVER use [[platters]] or build [[archival prints]] onto reels larger than 2000ft.
* If possible, use 2000 ft. reels and a dual-projector [[changeover]] system. NEVER use [[Platter systems|platters]] or build [[archival prints]] onto reels larger than 2000ft.
* If using a [[platter system]] to screen non-archival prints, routine maintenance and calibration of system is a must.  
* If using a [[platter system]] to screen non-archival prints, routine maintenance and calibration of system is a must.  
* If you're running small gauge film, do not have a changeover system, and have received permission from the archive to build onto larger reels, do not remove the heads and tails when you build the print. You'll have to close the dowser during the show as the heads and tails run through.  
* If you're running small gauge film, do not have a changeover system, and have received permission from the archive to build onto larger reels, do not remove the heads and tails when you build the print. You'll have to close the dowser during the show as the heads and tails run through.  
Line 50: Line 50:


==See Also==
==See Also==
[[Archival print]]
*[[Archival print]]
[[Film damage]]
*[[Film damage]]
[[Inspection]]
*[[Inspection]]
*[[Shipping]]


==External References==
==External References==

Revision as of 15:40, 17 February 2019

The 21st century projectionist's guiding principle: every print borrowed for exhibition, regardless of gauge or source, should be handled with a maximum of care and a minimum of shortcuts.

...exactly what this means is a matter of debate, of course. Below we will try to collectively come up with some general best practices. Always follow any specific instructions provided by the lender. Unless you own the print, it's their property and should be returned in the same (or better!) condition as it arrived.

Though some are addressed on this page, best practices specifically related to archival prints can be found here: Archival Prints

Before the show:

  • Open film cans as soon as print arrives to check for any damage incurred in shipping and to make sure you received the correct film (and all the reels are there).
  • Make sure your film inspection surface is clean.
  • Have a thorough inspection procedure for assessing print condition.
  • Carefully inspect the countdown leader and the cues at the end of each reel to ensure that your changeovers go smoothly.
  • Have an inspection form to facilitate communication about print condition.
  • Cleaning the projectors and checking all parts (including reels) for damage and wear routinely is a must.
  • Run test film to check frame and focus before the show, or run a test reel of the film (if possible).

During projection:

  • If possible, use 2000 ft. reels and a dual-projector changeover system. NEVER use platters or build archival prints onto reels larger than 2000ft.
  • If using a platter system to screen non-archival prints, routine maintenance and calibration of system is a must.
  • If you're running small gauge film, do not have a changeover system, and have received permission from the archive to build onto larger reels, do not remove the heads and tails when you build the print. You'll have to close the dowser during the show as the heads and tails run through.
  • Show the film in its proper aspect ratio using the appropriate lens and aperture plate.
  • Make sure a projectionist is present and attentive during the screening.
  • Check focus routinely. During changeover shows focus should be checked after every changeover.

After the show:

  • Wind the film with care, making sure the edges of the film are flush.
  • Secure the end of each reel with at least 6" of acid-free artist's tape.
  • When packing for shipping, be sure that the film is packed in material that will not harm the film (no packing peanuts or fibrous materials.

Practices to avoid

  • Using plastic shipping reels as take-up reels. Using damaged or bent reels.
  • Using automation systems and attaching automation tape to prints.
  • Projecting and rewinding prints on poorly maintained or damaged equipment.
  • Letting inexperienced or untrained people handle or project prints without supervision.
  • Making unnecessary marks on or adding unnecessary labels to prints.
  • Adding cue marks when usable cue marks are already present.
  • Cutting frames from a print or doing shoddy repair work.
  • Building or plattering archival prints.

Recommended Equipment

  • Projector models
    • avoid lens turrets
  • splicer varieties
  • cleaning supplies
  • rewind benches

Equipment to avoid

See Also

External References